4,3" touch screen operator panel, 480x272, ARM 600 MHz, TFT 16 milioni colors, RAM 128 MB, Nr1 USB host 2.0, Nr1 RS232/RS485, Nr1 RS485, Nr1 Ethernet

7" touch screen operator panel, 800x480, ARM 600 MHz, TFT 16 milioni colors, RAM 128 MB, Nr1 USB host 2.0, Nr1 RS232, Nr2 RS485, Nr 1 Ethernet

Converter with RTD (Pt100/ Pt1000/ Pt500/ Ni100) with 2,3,4 wires and 1 anaog output mA/V and 1 output signal mA/V, galvanic insolation 3-way, settable by DIP switch and software, microUSB port on The front side, Power supply 10~40Vdc / 19~2888 Vac

Universal converter with 1 analog input (mA, V, RTD, TCs, Ohm), 1 strobe input, 1 anaog output mA/V and 1 digital contact available as ALARM or STROBE, settable by DIP switch or software with microUSB. Power supply 10 ~ 40 Vdc / 19 ~ 28 Vac

Thermocouple to DC isolator / converter. Converter Thermocouples TCs (J/K/ E/ N/ S/ R/ B/ T) and provides a mA/V standard output signal. It’s completely programmable via MicroUSB/App. Power supply: 10~40 Vdc / 19~28 Vac / 50-60 Hz

Converter / isolator with a current input (+/-20mA) or voltage (100mV ~ 20V) and a current output (0 ~ 20 mA / 4 ~ 20mA) or voltage (0 ~ 10V / 2 ~ 10V). 1.5 kVac galvanic isolation, DIN rail mounting. Power supply: 10 to 40 Vdc or 19 to 28 Vac

Duplicator / isolator with universal input and 2 output (mA or V). Galvanic isolation 1.5 kVac 4-way, micro USB port, configurable by app, DIN rail mounting. Power supply: 10 to 40 Vdc or 19 to 28 Vac

DAQ module with 4 digital inputs/ 2 analog inputs (mA/ V) and 2 relay outputs @ 5A. Modbus RTU and Modbus TCP-IP communication with a 10/100 Mbps Ethernet port, 2 RS485 ports, a mini USB 2.0 port, power supply: 19 to 28 Vac, 11 to 40Vdc

AC/DC contactless TRMS direct and alternate current transducer, input for +/- 50A AC/DC, configurable by DIP switch or software, output from 0 to 10V, RS-485 port, Modbus RTU, power supply 10 to 28VDC, Includes 2 x A-DIN-T201 for DIN rail mounting

AC/DC contactless TRMS direct and alternate current transducer, input for +/- 100A AC/DC, configurable by DIP switch or software, output from 0 to 10V, RS-485 port, Modbus RTU, power supply 12 to 28VDC, Includes 2 x A-DIN-T201 for DIN rail mounting

AC/DC contactless TRMS direct and alternate current transducer to measure up to +/- 300 A DC/AC (csettable by DIP switch or Software) with 0~10Vdc output and ModBUS interface. Power supply 12~28 Vdc. Includes 2 x A-DIN-T201 for DIN rail mounting

Low power RTU, FTP version, 4DI, 2AI, 2DO, GSM antenna, DIN rail support

8-CH, NTC module with modbus RTU protocol (requires PC-DINAL2-17.5) .Reading value in resistance or temperature (° C, ° F, ° K). Each channel can be individually enabled and configured via DIP switches or software. Power supply: 10~40 Vdc or 19~28 Vac

ModBUS RTU/ASCII Compact Gateway. Power Supply: 10~40VDC; 19~28VAC. 1x Ethernet Port, 1x serial Port RS232/RS485 commutable. Modbus Bridge Finction: from ModBUS TCP-IP to Modbus RTU/ASCII or from ModBUS RTU/ASCII to Modbus TCP-IP.

GSM controller and alarm unit with 1 digital input and 1 SPDT output relay (3 A / 250 Vac). Quad band 850/900/1800/1900 MHz. Configuration by micro USB and partially via SMS. Includes antenna and baterry. Requieres 10~30 Vdc. Power supply not included

40A single phase energy counter 2 wires 1 DIN, MID certified

Power Supply Unit for MYALARM2 and R-KEY-LT

External GPS antenna - magnetic mount with SMA male connector for Z-PASS2, Z-PASS2-S and Z-UMTS models with integrated GPS receiver. Cable length: 3m.

GSM/3G/4G/LTE high-performance omnidirectional antenna, L=5mt

Rogowski Coil L=35cm Øint.11cm,100mV/1KA-50Hz,cable L=3mt.